[vortex] WakeOnLan with 3c905C-TX

[Markus Melms]

No I have not, 
but my driver is directly in the kernel and I dont
load it as a module.
Can I put this option somewhere else ?
Thanks Markus


On Mon, 27 May 2002 21:08:33 +0200
"Dr.Tilmann Bubeck" <bubeck@think-at-work.de> wrote:

> Markus,
> 
> Have you entered 
> 
> options 3c59x enable_wol=1
> 
> into /etc/modules.conf to enable WOL?
> 
> Till
> 
> 
> 
> 
> On Mon, 27 May 2002 20:41:36 +0200
> Markus Melms <hvx@cryptnet.de> wrote:
> 
> > Hi,
> > 
> > im trying to get wake-on-lan to work with the 3com 905C-TX card und
> > linux kernel 2.4.18.
> > It used to work some time ago with win95, so its probably a software
> > problem. When the system is powered off the LED doesnt light any more
> > and the system doesnt boot up when executing etherwake..
> > 
> > Below is some output and I would be happy to provide even more when
> > needet. Thanks for any help,
> > 	Markus
> > 
> > joe:~# ./pciconfig -#7 -M
> > pci-config.c:v2.02 1/8/2001 Donald Becker (becker@scyld.com)
> >  http://www.scyld.com/diag/index.html
> > Device #7 at bus 0 device/function 9/0.
> >   920010b7 02100007 02000074 00002008 0000e401 e7000000 00000000
> >   00000000 00000000 00000000 00000000 100010b7 e6000000 000000dc
> >   00000000 0a0a010b 00000000 00000000 00000000 00000000 00000000
> >   00000000 00000000 00000000 00000000 00000000 00000000 00000000
> >   00000000 00000000 00000000 00000000 00000000 00000000 00000000
> >   00000000 00000000 00000000 00000000 00000000 00000000 00000000
> >   00000000 00000000 00000000 00000000 00000000 00000000 00000000
> >   00000000 00000000 00000000 00000000 00000000 00000000 fe020001
> >   b7004000 00000000 00000000 00000000 00000000 00000000 00000000
> >   00000000 Base Address 0: I/O at 0000e400.
> >   Base Address 1: Memory at e7000000.
> >   Extended capabilities, first structure at offset 0xdc.
> >   Extended PCI capability type 1 at 0xdc, next 0.
> >    Power management entry ver. 2: Capabilities fe02, Ctrl 4000, Event
> >    b700. Power state D0.
> > 
> > joe:~# ./vortex-diag -a
> > vortex-diag.c:v2.06 4/18/2002 Donald Becker (becker@scyld.com)
> >  http://www.scyld.com/diag/index.html
> > Index #1: Found a 3c905C Tornado 100baseTx adapter at 0xe400.
> > The Vortex chip may be active, so FIFO registers will not be read.
> > To see all register values use the '-f' flag.
> > Initial window 7, registers values by window:
> >   Window 0: 0000 0000 0000 0000 0000 00bf ffff 0000.
> >   Window 1: FIFO FIFO 0700 0000 0000 007f 0000 2000.
> >   Window 2: 5000 66da bdc2 0000 0000 0000 0052 4000.
> >   Window 3: 0000 0380 05ea 0020 000a 0800 0800 6000.
> >   Window 4: 0000 0000 0000 0cfa 0001 8880 2000 8000.
> >   Window 5: 1ffc 0000 0000 0600 0807 06ce 06c6 a000.
> >   Window 6: 0000 0000 0000 c500 2000 3f62 2f88 c000.
> >   Window 7: 0000 0000 0000 0000 0000 0000 0000 e000.
> > Vortex chip registers at 0xe400
> >   0xE410: **FIFO** 00000000 0000005b *STATUS*
> >   0xE420: 00000020 00000000 00080000 00000004
> >   0xE430: 00000000 47b0b850 012cc130 00080004
> >  Indication enable is 06c6, interrupt enable is 06ce.
> >  No interrupt sources are pending.
> >  Transceiver/media interfaces available:  100baseTx 10baseT.
> > Transceiver type in use:  Autonegotiate.
> >  MAC settings: full-duplex.
> >  Station address set to 00:50:da:66:c2:bd.
> >  Configuration options 0052.
> > 
> > joe:~# dmesg
> > --cut---
> > PCI: Found IRQ 11 for device 00:09.0
> > PCI: Sharing IRQ 11 with 00:07.2
> > 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
> > 00:09.0: 3Com PCI 3c905C Tornado at 0xe400. Vers LK1.1.16
> > --cut---
> > _______________________________________________
> > vortex mailing list
> > vortex@scyld.com
> > http://www.scyld.com/mailman/listinfo/vortex
> 
> 
> -- 
> +-------+-------------------------------------------------------------+
> |       | dr. tilmann bubeck               reinform medien- und       |
> | rein  |                                  informationstechnologie AG |
> | form  | cell.: +49 (172) 8 84 29 72      koenigstrasse 80           |
> |    AG | fax  : +49 (711) 7 22 77 34      70173 stuttgart / germany  |
> |       | email: t.bubeck@reinform.de      http://www.reinform.de     |
> +-------+----------------------------------------------(in gruendung)-+