[vortex] Problems with 3Com 3C3SH573BT

[Greg Swallow]

Hello, all,

If anyone could be of assistance...

I've got a problem starting my system up with the aforementioned card in
its socket (32-bit cardbus).  I haven't seen any mention of this card on
the mailing list archives, so maybe it's a new problem?

Here's dmesg output from when the system boots up with the card in its
socket.

Intel ISA/PCI/CardBus PCIC probe:
PCI: Found IRQ 10 for device 00:08.0
PCI: The same IRQ used for device 00:0d.0
PCI: Found IRQ 10 for device 00:08.1
  Ricoh RL5C478 rev 80 PCI-to-CardBus at slot 00:08, mem 0x10000000
    host opts [0]: [pci only] [io 3/6/1] [mem 3/6/1] [pci irq 10] [lat
168/176] [bus 2/5]
    host opts [1]: [pci only] [io 3/6/1] [mem 3/6/1] [pci irq 10] [lat
168/176] [bus 6/9]
    PCI card interrupts, PCI status changes
cs: cb_alloc(bus 2): vendor 0x10b7, device 0x5257
cs: IO port probe 0x0c00-0x0cff: clean.
  fn 0 bar 1: io 0x200-0x2ff
  fn 0 bar 2: mem 0xffe1000-0xffe107f
  fn 0 bar 3: mem 0xffe0000-0xffe007f
  fn 0 rom: mem 0xffc0000-0xffdffff
  irq 10
cs: cb_enable(bus 2)
  bridge io map 0 (flags 0x21): 0x200-0x2ff
  bridge mem map 0 (flags 0x1): 0xffc0000-0xffe1fff
vortex_attach(device 02:00.0)
eth0: 3Com 3CCFE575CT Tornado CardBus at 0x200,  00:04:76:3b:e9:0f, IRQ
10
  product code 'RG' rev 10.0 date 08-14-01
eth0: CardBus functions mapped 0ffe0000->c9088000.
  8K byte-wide RAM 5:3 Rx:Tx split, MII interface.
  MII transceiver found at address 0, status 7809.
  Enabling bus-master transmits and whole-frame receives.
spurious 8259A interrupt: IRQ7.
vortex_detach(eth0)
cs: cb_disable(bus 2)
cs: cb_release(bus 2)
cs: cb_free(bus 2)

I removed the card at the end because the system starts acting strange.
And here I re-inserted the card, which usually fixes the problem.

cs: cb_alloc(bus 2): vendor 0x10b7, device 0x5257
3c59x.c:v0.99Q 5/16/2000 Donald Becker, becker@scyld.com
  http://www.scyld.com/network/vortex.html
cs: cb_config(bus 2)
  fn 0 bar 1: io 0x200-0x2ff
  fn 0 bar 2: mem 0xffe1000-0xffe107f
  fn 0 bar 3: mem 0xffe0000-0xffe007f
  fn 0 rom: mem 0xffc0000-0xffdffff
  irq 10
cs: cb_enable(bus 2)
  bridge io map 0 (flags 0x21): 0x200-0x2ff
  bridge mem map 0 (flags 0x1): 0xffc0000-0xffe1fff
vortex_attach(device 02:00.0)
eth0: 3Com 3CCFE575CT Tornado CardBus at 0x200,  00:04:76:3b:e9:0f, IRQ
10
  product code 'RG' rev 10.0 date 08-14-01
eth0: CardBus functions mapped 0ffe0000->c90a5000.
  8K byte-wide RAM 5:3 Rx:Tx split, MII interface.
  MII transceiver found at address 0, status 7809.
  Enabling bus-master transmits and whole-frame receives.

I think I've isolated and killed all the PCMCIA problems on this
laptop.  However, I may be wrong and if I am I'll gladly accept "go
away" as an answer.  Have any of you had any experiences with this card?

Thanks!

-- 
 "There's nothing that the proper funk cannot render funkable" --
+--------------+--------------------+---------------+-- G. Clinton +
| Greg Swallow | Assistant Sysadmin | accessIndiana | 888.4IN.EGOV |
+--------------+--------------------+---------------+----(446.3468)+