same problem "=?iso-8859-1?Q?cant=B4t?= ping host" with 3c575 PCMCIA
Harald Wolf
haraldwolf@swol.de
Wed Mar 31 00:40:05 1999
Hi,
i have a 3C575-TX PCMCIA-Card which returns no error but canīt ping any
host !!
i am working in a 100Mbit Network and the 100MBit LED is on.
can someone help me with my problem ???
below i have the output (dmesg,/var/log/messages,ifconfig,route -n and
/proc/interrupts)
*****************************************************************************
ifconfig reports
*****************************************************************************
lo Link encap:Local Loopback
inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0
UP BROADCAST LOOPBACK RUNNING MTU:3584 Metric:1
RX packets:40 errors:0 dropped:0 overruns:0 frame:0
TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
dummy0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
inet addr:192.168.1.21 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
eth0 Link encap:Ethernet HWaddr 00:60:08:01:C7:F9
inet addr:192.168.1.21 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0
Interrupt:3 Base address:0x100
*****************************************************************************
route -n reports
*****************************************************************************
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
192.168.1.21 0.0.0.0 255.255.255.255 UH 0 0 0
dummy0
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0
eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 2
lo
*****************************************************************************
System boot messages from dmesg
*****************************************************************************
Starting PCMCIA services:Linux PCMCIA Card Services 3.0.6
kernel build: 2.0.36 #1 Fri Dec 11 16:26:51 /etc/localtime 1998
options: [pci] [cardbus]
Intel PCIC probe:
TI 1250A PCI-to-CardBus at bus 0 slot 2, mem 0x20822000, 2 sockets
host opts [0]: [ring] [pwr save] [isa irq] [pci irq 11] [lat
168/176] [bus 1/3]
host opts [1]: [ring] [pwr save] [isa irq] [pci irq 11] [lat
168/176] [bus 4/6]
ISA irqs (scanned) = 3,4,7,9,10,15 status change on irq 15
cardmgr.
cardmgr[70]: starting, version is 3.0.6
cardmgr[70]: watching 2 sockets
cs: IO port probe 0x1000-0x17ff: excluding 0x15e8-0x15ef
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f
0x388-0x38f 0x3b8-0x3df 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
3c59x.c:v0.99H 11/17/98 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
cs: cb_config(bus 4): vendor 0x10b7, device 0x5057
fn 0 bar 1: io 0x100-0x13f
fn 0 rom: mem 0xa0010000-0xa001ffff
cs: cb_enable(bus 4)
bridge io map 0 (flags 0x21): 0x100-0x13f
bridge mem map 0 (flags 0x1): 0xa0010000-0xa001ffff
vortex_attach(bus 4, function 0, device 5057)
eth0: 3Com 3c575 Boomerang CardBus at 0x100, 00:60:08:01:c7:f9, IRQ 3
8K word-wide RAM 3:5 Rx:Tx split, autoselect/MII interface.
MII transceiver found at address 0, status 7809.
Enabling bus-master transmits and whole-frame receives.
*******************************************************************************
/var/log/messages when removing the card
*******************************************************************************
Mar 31 07:29:49 xtp kernel: vortex_detach(eth0)
Mar 31 07:29:49 xtp kernel: ERROR 'eth0' busy and not MOD_IN_USE.
Mar 31 07:29:49 xtp kernel: cs: cb_disable(bus 4)
Mar 31 07:29:49 xtp kernel: cs: cb_release(bus 4)
Mar 31 07:29:49 xtp cardmgr[70]: shutting down socket 1
Mar 31 07:29:49 xtp cardmgr[70]: executing: './network stop eth0'
Mar 31 07:29:50 xtp cardmgr[70]: + eth0: unknown interface.
Mar 31 07:29:51 xtp cardmgr[70]: + eth0: unknown interface.
Mar 31 07:29:51 xtp cardmgr[70]: + Shutting down
routing^[[71G^[[32mdone^[[m
Mar 31 07:29:51 xtp cardmgr[70]: executing: 'rmmod 3c575_cb'
Mar 31 07:29:51 xtp cardmgr[70]: executing: 'rmmod cb_enabler'
*******************************************************************************
/var/log/messages when inserting the card
*******************************************************************************
Mar 31 07:31:58 xtp cardmgr[70]: initializing socket 1
Mar 31 07:31:58 xtp cardmgr[70]: socket 1: 3Com 3c575-TX Fast EtherLink
XL
Mar 31 07:31:59 xtp cardmgr[70]: executing: 'insmod
/lib/modules/2.0.36/pcmcia/cb_enabler.o'
Mar 31 07:31:59 xtp cardmgr[70]: executing: 'insmod
/lib/modules/2.0.36/pcmcia/3c575_cb.o'
Mar 31 07:31:59 xtp kernel: 3c59x.c:v0.99H 11/17/98 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
Mar 31 07:31:59 xtp kernel: cs: cb_config(bus 4): vendor 0x10b7, device
0x5057
Mar 31 07:31:59 xtp kernel: fn 0 bar 1: io 0x100-0x13f
Mar 31 07:31:59 xtp kernel: fn 0 rom: mem 0xa0010000-0xa001ffff
Mar 31 07:31:59 xtp kernel: cs: cb_enable(bus 4)
Mar 31 07:31:59 xtp kernel: bridge io map 0 (flags 0x21): 0x100-0x13f
Mar 31 07:31:59 xtp kernel: bridge mem map 0 (flags 0x1):
0xa0010000-0xa001ffff
M
Mar 31 07:31:59 xtp kernel: vortex_attach(bus 4, function 0, device
5057)
Mar 31 07:31:59 xtp kernel: eth0: 3Com 3c575 Boomerang CardBus at
0x100, 00:60:08:01:c7:f9, IRQ 3
Mar 31 07:31:59 xtp kernel: 8K word-wide RAM 3:5 Rx:Tx split,
autoselect/MII interface.
Mar 31 07:31:59 xtp kernel: MII transceiver found at address 0, status
7809.
Mar 31 07:31:59 xtp kernel: Enabling bus-master transmits and
whole-frame receives.
Mar 31 07:31:59 xtp cardmgr[70]: executing: './network start eth0'
Mar 31 07:31:59 xtp cardmgr[70]: + Setting up network device eth0
Mar 31 07:32:00 xtp cardmgr[70]: + ^[[1A^[[71G^[[32mdone^[[m
Mar 31 07:32:00 xtp cardmgr[70]: + Setting up routing (using
/etc/route.conf)^[[71G^[[32mdone^[[m
*******************************************************************************
0: 92877 timer
1: 3144 keyboard
2: 0 cascade
3: 11 eth0
8: 2 + rtc
12: 10956 PS/2 Mouse
13: 1 math error
14: 4060 + ide0
15: 8 i82365