[tulip] RH7.1 on Presario 1700T laptop

[samir Purohit]

 Hi !!

 Folks...I did a bit more research and I managed to
get the latest tulip.c and pci-scan.c compiled without
any error messages. But insmod command throws a lot of
unresolved symbols errors. e.g. insmod pci-scan.o
gives
following output:

pci-scan.o: unresolved symbol pci_write_config_byte
pci-scan.o: unresolved symbol kmalloc
pci-scan.o: unresolved symbol pci_find_class
pci-scan.o: unresolved symbol __check_region
pci-scan.o: unresolved symbol pci_read_config_byte
pci-scan.o: unresolved symbol pci_read_config_dword
pci-scan.o: unresolved symbol __ioremap
pci-scan.o: unresolved symbol pci_read_config_word
pci-scan.o: unresolved symbol kfree
pci-scan.o: unresolved symbol pci_set_master
pci-scan.o: unresolved symbol pci_write_config_dword
pci-scan.o: unresolved symbol pci_write_config_word
pci-scan.o: unresolved symbol printk
pci-scan.o: unresolved symbol ioport_resource
 
 This still causes 'initializing eth0: delaying.....
failed' error. The output of tulip-diag is as follows:

[root@localhost tulip-0.92wax]# ./tulip-diag -aem
tulip-diag.c:v2.08 5/15/2001 Donald Becker
(becker@scyld.com)
 http://www.scyld.com/diag/index.html
Index #1: Found a Conexant LANfinity adapter at
0x1400.
Conexant LANfinity chip registers at 0x1400:
 0x00: fff80000 ffffffff ffffffff 00000000 00000000
f4008800 e00c0040 7bfe0000
 0x40: fffe0000 fff080e8 fffe0000 fffe0000 ffffffff
ffffffff ffffffff f7f9fec8
 Extended registers:
 80: cc008800 cbfe0000 f0000018 00000000 ffffffff
00000000 00000000 00000000
 a0: ffffffff 00000000 00000000 00000000 00000000
00000000 00000000 00000000
 c0: 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000
 e0: 00000000 00000000 00000000 00000000 ffffffff
00000000 00000000 00000000
 Port selection is MII, half-duplex.
 Transmit stopped, Receive stopped, half-duplex.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 128.
 Interrupt sources are pending!  CSR5 is f4008800.
   Timer expired indication.
EEPROM 256 words, 8 address bits.
Conexant EEPROM format is undocumented.
 MII PHY found at address 1, status 0x7809.
 MII PHY found at address 0, status 0x7809.
 MII PHY #1 transceiver registers:
   1000 7809 0022 1720 01e1 0000 0004 2001
   1000 7809 0022 1720 01e1 0000 0004 2001
   1000 7809 0022 1720 01e1 0000 0004 2001
   0000 0000 0000 0000 01e1 2001 0000 8c00.
 MII PHY #0 transceiver registers:
   1000 7809 0022 1720 01e1 0000 0004 2001
   1000 7809 0022 1720 01e1 0000 0004 2001
   1000 7809 0022 1720 01e1 0000 0004 2001
   0000 0000 0000 0000 01e1 2001 0000 8c00.

 Can anybody suggest if I have missed anything? Just
to refresh, I have Compaq Presario 17XL3 with RedHat
Linux 7.1 (kernel 2.4.2.2) with the Conexant LanFinity
ethernet card.
 
 Thanx..
 Cheers,
 Sam.



__________________________________________________
Do You Yahoo!?
Send FREE video emails in Yahoo! Mail!
http://promo.yahoo.com/videomail/