[tulip] Netgear FA310TX rev D2 NIC

[Bruce Bales]

I'm new to Linux.  Can't find any messages with my problem

I have a Netgear FA310TX rev D2 ethernet board with LC82C169C chip (not
LC82C168c).  Netgear says
board is based on DEC 21040 (tulip).  Also have an ISA NE2000 card in
same machine.  Running Mandrake 7.1  ISA board sets up fine with cable
modem.  Switch cable to Netgear PCI board and change configuration to
DHCP for it and Linux looks at it for 60 seconds (Bringing up eth0) then
says OK.  But it didn't DHCP an address. And won't ping except
127.0.0.1.

Mandrake has tulip.c:v0.91g-ppc  7/16/99.  Netgear says to get the
latest tulipdriver - 0.90Q.  I assume 0.91G should be OK, but it doesn't
work on this card or another in another machine.  They won't ping others
or each other.  Is there a revised driver?

Have part of dmesg, proc pci and ifconfig below.

Would appreciate any help.  Have been struggling with this for weeks.
Bruce Bales
_________________________________________________
part of dmesg follows:
Linux version 2.2.15-4mdksecure (chmou@kenobi.mandrakesoft.com) (gcc
version 2.95.3 19991030 PCI: PCI BIOS revision 2.10 entry at 0xfb180
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 32768 bhash 32768)
Initializing RT netlink socket
tulip.c:v0.91g-ppc 7/16/99 becker@cesdis.gsfc.nasa.gov
eth0: Lite-On 82c168 PNIC rev 32 at 0x6000, 00:A0:CC:5C:AB:35, IRQ 10.
eth0:  MII transceiver #1 config 3000 status 782d advertising 01e1.
ne.c:v1.10 9/23/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)
NE*000 ethercard probe at 0x280: 00 00 21 69 7b 86
eth1: NE2000 found at 0x280, using IRQ 11.

==============================================
part of proc pci:
PCI devices found:
  Bus  0, device  15, function  0:
    Ethernet controller: LiteOn LNE100TX (rev 32).
      Medium devsel.  Fast back-to-back capable.  IRQ 10.  Master
Capable.  Latency=32.
      I/O at 0x6000 [0x6001].
      Non-prefetchable 32 bit memory at 0xf0410000 [0xf0410000].

=======================================================
ifconfig:
eth0      Link encap:Ethernet  HWaddr 00:A0:CC:5C:AB:35
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:8 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          Interrupt:10 Base address:0x6000

eth1      Link encap:Ethernet  HWaddr 00:00:21:69:7B:86
          inet addr:192.168.100.1  Bcast:192.168.100.255
Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          Interrupt:11 Base address:0x280

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:3924  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0