CNET PRO120

[James Barwick]

I have a CNET Pro120 Fast Ethernet 100BaseTX/10BaseT adapter.

please help!  No dice with 0.90z.  Based on the response from tulip-diag
below, do you think that this card is a no-go? No, I don't have a bus
mouse.  Yes, IRQ 12 is available. Yes, this card is awesome when I boot
to windows95.

One more thing.  /proc/pci shows the following for this card:

Bus 0, device 10, function 0:
     Ethernet controller: Unknown vendor MX98715 / MX98725 (rev 32).
     Medium devsel. Fast back-to-back capable. IRQ 12. Master Capable.
     Latency=32. Min Gnt=8. Max Lat=56.
     I/O at 0xe400
     Non-prefetchabel 32 bit memory at 0xfbfdf000.

Loading tulip.o responds in /var/log/messages:

Apr 10 22:34:16 lighthouse kernel: tulip.c:v0.90z 4/7/99
becker@cesdis.gsfc.nasa.gov
Apr 10 22:34:16 lighthouse kernel: eth1: Macronix 98715 PMAC rev 32 at
0xe400, 00:80:AD:97:F6:AD, IRQ 12.

Seems OK.  I get a link light on my HUB.

Running ifconfig responds on console:

SIOCSIFFLAGS: Try again

Running ifconfig responds in /var/log/messages:

Apr 10 22:34:25 lighthouse modprobe: can't locate module pf -4
Apr 10 22:34:25 lighthouse modprobe: can't locate module pf -3
Apr 10 22:34:25 lighthouse modprobe: can't locate module pf -5

Here is some output from tulip-diag:

No parameters:
tulip-diag.c:v1.09 4/9/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Unable to find a Tulip card in /proc/pci.
If there is a Tulip card in the machine, explicitly set the I/O port
address using '-p <ioaddr>'

Parameters: -p 0xe400
tulip-diag.c:v1.09 4/9/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
 Port selection is 10mpbs-serial, half-duplex.
 Transmit stopped,Receive stopped, half-duplex.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 72.
 Use '-a' to show device registers,
     '-e' to show EEPROM contents,
  or '-m' to show MII management registers.

Parameters: -p 0xe400 -a
tulip-diag.c:v1.09 4/9/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Digital Tulip, unknown type Tulip chip registers at 0xe400:
   fe580000 ffffffff ffffffff 00fba000 00fde000 e4000000 e1000000
e7fe0000
   fffe0000 0fffcf00 fffffdff fffe0000 000050ca ffff0000 ffffffff
fff00000
 Port selection is 10mpbs-serial, half duplex
 Transmit stopped,Receive stopped, half-duplex.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 72.

Parameters:  -p 0xe400 -e
tulip-diag.c:v1.09 4/9/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
 Port selection is 10mpbs-serial, half duplex
 Transmit stopped,Receive stopped, half-duplex.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 72.
 A simplified EEPROM data table was found.
 The EEPROM does not contain transceiver control information.

Parameters:  -p 0xe400 -m
tulip-diag.c:v1.09 4/9/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
 Port selection is 10mpbs-serial, half duplex
 Transmit stopped,Receive stopped, half-duplex.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 72.
 ***WARNING***: No MII transceivers found!