[yellowfin] GNIC II Driver

shreenivasa HV shreenihv@hotmail.com
Tue, 01 May 2001 19:56:08 -0500


Does the driver which comes with kernel 2.4 work fine???? It never works for 
me for a simple setup of two machines connected thru' corss-over. Also, I 
have never been able to get two cards in a single machine working. If anyone 
has any idea about it do post it.

Thanks,
Shreeni.


>From: Keith Underwood <keithu@parl.clemson.edu>
>To: shreenivasa HV <shreenihv@hotmail.com>
>CC: <yellowfin@scyld.com>
>Subject: Re: [yellowfin] GNIC II Driver
>Date: Sun, 22 Apr 2001 21:32:33 -0400 (EDT)
>
>Hmmm... Unsure if they actually build the module in the stock distro for
>that kernel.  Also not sure if kudzu (their new hardware detection thing)
>would detect it one way or the other.  It's entirely possible the driver
>module was there and just needed to be inserted...
>
>					Keith
>
>On Sun, 22 Apr 2001, shreenivasa HV wrote:
>
> > Well, it never recognized my card when the card was inserted for the 
>first
> > time.
> > Any tweeking needed?? And I have made it sure that it's not the problem 
>with
> > the card, PCI slot, etc.
> >
> >
> > >From: Keith Underwood <keithu@parl.clemson.edu>
> > >To: shreenivasa HV <shreenihv@hotmail.com>
> > >CC: <yellowfin@scyld.com>
> > >Subject: Re: [yellowfin] GNIC II Driver
> > >Date: Sun, 22 Apr 2001 17:29:27 -0400 (EDT)
> > >
> > >The driver distributed in the 2.2.16 kernel should work fine.
> > >
> > >				Keith
> > >
> > >On Sun, 22 Apr 2001, shreenivasa HV wrote:
> > >
> > > > Hi,
> > > > I was trying to install the Packet Engines GNIC-II gigabit ethernet 
>card
> > > > onto some of my Linux systems. I am running Redhat Linux 7.0 with 
>kernel
> > > > version 2.2.16. The systems are P-III 600MHz. I have connected two
> > >systems
> > > > which have the GNIC-II cards to each other through a cross-over
> > > > optical-fibre cable. I downloaded the driver available from the 
>Scyld
> > >site -
> > > > http://www.scyld.com/network/modules.html and exactly followed the
> > > > instructions. Also I inserted the PCI-SCAN and HAMACHI modules.
> > > >
> > > > When I try to ping one machine from another after 15 pings the ping
> > > > program hangs consistently. In each machine I have added a static 
>route
> > >to
> > > > the other machine as the IP gateway.
> > > > I even tried to ssh between them, but that again hangs during log 
>on. It
> > > > seems like only the first few packets go through.
> > > > After some time the receiving end starts showing this error message.
> > > >
> > > > "eth1: Hamachi transmit timed out, status 00003803"
> > > >
> > > > Has anyone had any similar problems and does anyone know of a fix 
>for
> > >this?
> > > >
> > > > Thanks,
> > > > Shreeni.
> > > > _________________________________________________________________
> > > > Get your FREE download of MSN Explorer at http://explorer.msn.com
> > > >
> > > >
> > > > _______________________________________________
> > > > yellowfin mailing list
> > > > yellowfin@scyld.com
> > > > http://www.scyld.com/mailman/listinfo/yellowfin
> > > >
> > >
> > 
> >---------------------------------------------------------------------------
> > >Keith Underwood                   Parallel Architecture Research Lab 
>(PARL)
> > >keithu@parl.clemson.edu                                  Clemson 
>University
> > >
> >
> > _________________________________________________________________
> > Get your FREE download of MSN Explorer at http://explorer.msn.com
> >
>
>---------------------------------------------------------------------------
>Keith Underwood                   Parallel Architecture Research Lab (PARL)
>keithu@parl.clemson.edu                                  Clemson University
>

_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com