Bug report, as much information as I can give...
Winged Wolf
winged@spastic.org
Tue Dec 28 13:53:24 1999
I've tried all 3 PCI slots.
/proc/interrupts shows IRQ 5 assigned to this device in the first slot; it
shows 10 in the second and 11 in the third.
This is a brand-new card that I got as part of my Vectra VL; I have
another Vectra VL with exactly the same hardware configuration that shows
exactly the same symptoms.
Whee. This is starting to look like HP made a modification to the card.
---
Mat Butler, Winged Wolf <winged@spastic.org>
SPASTIC Web Engineer SPASTIC Server Administrator
On Tue, 28 Dec 1999, Ted Matsumura wrote:
> Have you tried different PCI slots? What does /proc/interrupts show it
> using or sharing with? Do you have another card to try? Your particular
> one may be bad.
>
> Ted
>
> > -----Original Message-----
> > From: owner-linux-vortex-bug@beowulf.org
> > [mailto:owner-linux-vortex-bug@beowulf.org]On Behalf Of Winged Wolf
> > Sent: Monday, December 27, 1999 10:15 PM
> > To: Romanenko Mikhail
> > Cc: linux-vortex-bug@beowulf.gsfc.nasa.gov
> > Subject: Re: Bug report, as much information as I can give...
> >
> >
> > I did try this, and it seems to be stuck at the same point as Mr. Becker's
> > driver. (Specifically, at this point, it appears to be a problem with the
> > PCI bus mastering... like it says it's being enabled, but the PCI BIOS
> > doesn't recognize it.)
> >
> > Thanks!
> >
> > ---
> > Mat Butler, Winged Wolf <winged@spastic.org>
> > SPASTIC Web Engineer SPASTIC Server Administrator
> >
> >
> > On Tue, 28 Dec 1999, Romanenko Mikhail wrote:
> >
> > > I had another problem with 3Com 905B (and 3Com 980). I wrote to
> > the list about it but nobody answered. Shortly speaking NIC
> > swithed from 100 b/s to 10 b/s after machine reboot.
> > > Hab was hanged often. After I install 3c90x driver from
> > http://support.3com.com/infodeli/tools/nic/linuxdownload.htm
> > everything has been working fine. Perhaps it helps you too.
> > >
> > > Mikhail.
> > >
> > > -----Original Message-----
> > > From: Winged Wolf <winged@spastic.org>
> > > To: linux-vortex-bug@beowulf.gsfc.nasa.gov
> > <linux-vortex-bug@beowulf.gsfc.nasa.gov>
> > > Date: Tuesday, December 28, 1999 4:49 AM
> > > Subject: Bug report, as much information as I can give...
> > >
> > >
> > > >Heya, I've got a bit of a problem. I've got two machines (HP
> > Vectra VLi8
> > > >MTs) with what appear to be 3c509B cards in them.
> > > >
> > > >Trying to install Debian 2.1 (from a CD I bought at Fry's, not marked
> > > >'official'), everything goes wonderfully. Until I try to bring up the
> > > >network interface.
> > > >
> > > >The symptom is, the module loads properly, but nothing comes in or out.
> > > >tcpdump doesn't show anything going across the line at all.
> > Can't ping,
> > > >can't be pinged.
> > > >
> > > >I'm using the 3c59x.c:v0.99H 11/17/98 driver (the one included
> > with kernel
> > > >revision 2.2.12).
> > > >
> > > >Trying to work around this problem, I've tried the following
> > > >combinations of options:
> > > >options=0 full_duplex=0
> > > >options=8 full_duplex=0
> > > >options=9 full_duplex=0
> > > >
> > > >9 doesn't work, because I'm not using an AUI transceiver. I'm
> > supposed to
> > > >be using 10baseT, half-duplex. The hub (Netgear EN104TP) does
> > not show a
> > > >link light. I've replaced the cable with a Known Good, and swapped the
> > > >port on the hub with a Known Good.
> > > >
> > > >When I start up with:
> > > >options=8 full_duplex=0 debug=9
> > > >
> > > >I get:
> > > >
> > > >eth0: 3Com 3c905B Cyclone 100baseTx at 0x1080,
> > 00:50:da:1c:9d:7d, IRQ 10
> > > > Internal Config register is 1800000, transceivers 0xa.
> > > > 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
> > > > Media override to transceiver type 0 (10baseT).
> > > > Enabling bus-master transmits and whole-frame receives.
> > > >eth0: Media override to transceiver 0 (10baseT).
> > > >eth0: Initial media type 10baseT.
> > > >
> > > >Then, when I ifconfig eth0 192.6.1.107 netmask 255.255.255.0:
> > > >
> > > >eth0: vortex_open() InternalConfig 01000000.
> > > >eth0: vortex_open() irq 10 media status 8880.
> > > >eth0: Filling in the Rx ring.
> > > >eth0: Media selection timer tick happened, 10baseT.
> > > >eth0: Media 10baseT has link beat, 88c0.
> > > >eth0: Media selection timer finished, 10baseT.
> > > >
> > > >When I ping a host that I know is up, and is located on the same hub as
> > > >this machine:
> > > >
> > > >eth0: Trying to send a packet, Tx index 0.
> > > >eth0: interrupt, status e201, latency 2 ticks.
> > > >eth0: in interrupt loop, status e201.
> > > >eth0: exiting interrupt, status e000.
> > > >eth0: Trying to send a packet, Tx index 1.
> > > >eth0: interrupt, status e201, latency 2 ticks.
> > > >eth0: In interrupt loop, status e201.
> > > >eth0: exiting interrupt, status e000.
> > > >eth0: Trying to send a packet, Tx index 2.
> > > >eth0: interrupt, status e201, latency 2 ticks.
> > > >eth0: In interrupt loop, status e201.
> > > >eth0: exiting interrupt, status e000.
> > > >eth0: Trying to send a packet, Tx index 3.
> > > >eth0: interrupt, status e201, latency 1 ticks.
> > > >eth0: In interrupt loop, status e201.
> > > >eth0: exiting interrupt, status e000.
> > > >...
> > > >
> > > >And so on. (It's now on index 50.) And that was with a single ping
> > > >packet. (Every 10 seconds or so, it tries 3 more times, one second
> > > >between each try.)
> > > >
> > > >This is -not- the way that things are supposed to be working,
> > I'd assume.
> > > >What information can I give you that will help track this problem down?
> > > >
> > > >---
> > > >Mat Butler, Winged Wolf <winged@spastic.org>
> > > >SPASTIC Web Engineer SPASTIC Server Administrator
> > > >
> > > >
> > >
> >
>