[tulip] Full-Duplex not working on older lne100tx

[Sven Eichner]

Hi Erik,

i am not sure but do you not mean an 100/10 Mbit Dual-Speed HUB ? That only
switch 10 mbit /s transfers ?

This is internaly a hub and not a switch and so far it can not work with
full-duplex.

Regards,
Sven

----- Original Message -----
From: "Erik Myllymaki" <erikm@islandnet.com>
To: <tulip@scyld.com>
Sent: Thursday, October 19, 2000 12:39 AM
Subject: Re: [tulip] Full-Duplex not working on older lne100tx


> >> eth0: Lite-ON 82c168 PNIC rev 17 at 0xda00, <mac address>,IRQ 5
>
> >That's likely a SYM transceiver, but you should run the 'tulip-diag
> -afm'
> >program to verify.
>
> Just used the tulip-diag:
>
> tulip-diag.c:v2.04 9/26/2000 Donald Becker (becker@scyld.com)
>  http://www.scyld.com/diag/index.html
> Index #1: Found a Lite-On 82c168 PNIC adapter at 0xda00.
> Lite-On 82c168 PNIC chip registers at 0xda00:
>   00008000 01ff0000 00004000 00003810 00003a10 06660010 01862202
> 0001fbef
>   00000000 00000000 00003af0 0f61d068 0000003f 00000000 00000000
> 10000000
>   00000000 00000000 ffff0002 000000bf 09f989f0 00003880 0f5f4010
> 2001f868
>   00000000 00000000 00000000 00000000 00000000 00000000 00000000
> 00000000
>  Port selection is 100mbps-SYM/PCS 100baseTx scrambler, full-duplex.
>  Transmit started, Receive started, full-duplex.
>   The Rx process state is 'Waiting for packets'.
>   The Tx process state is 'Idle'.
>   The transmit threshold is 128.
>  MII PHY found at address 1, status 0x8210.
>  MII PHY found at address 2, status 0x8410.
>  MII PHY found at address 3, status 0x8610.
>  MII PHY found at address 4, status 0x8810.
>  MII PHY #1 transceiver registers:
>    8200 8210 8220 8230 8240 8250 8260 8270
>    8280 8290 82a0 82b0 82c0 82d0 82e0 82f0
>    8300 0000 8320 8330 8340 8350 8360 8370
>    8380 0000 83a0 83b0 83c0 83d0 83e0 83f0.
>  MII PHY #2 transceiver registers:
>    8400 0000 8420 8430 8440 8450 8460 8470
>    8480 0000 84a0 84b0 84c0 84d0 84e0 84f0
>    8500 8510 8520 8530 8540 8550 8560 8570
>    8580 8590 85a0 85b0 85c0 85d0 85e0 85f0.
>  MII PHY #3 transceiver registers:
>    8600 0000 8620 8630 8640 8650 8660 8670
>    8680 8690 86a0 86b0 86c0 86d0 86e0 86f0
>    8700 0000 8720 8730 8740 8750 8760 8770
>    8780 8790 87a0 87b0 87c0 87d0 87e0 87f0.
>  MII PHY #4 transceiver registers:
>    8800 0000 8820 8830 8840 8850 8860 8870
>    8880 0000 88a0 88b0 88c0 88d0 88e0 88f0
>    8900 8910 8920 8930 8940 8950 8960 8970
>    8980 8990 89a0 89b0 89c0 89d0 89e0 89f0.
>
> ?? Says that it is in full-duplex mode, yet my switch says otherwise. ??
>
> On another note, I tried to compile my kernel with the latest tulip.c.
> Fixed the *buglet* at line 131 after running into some unresolved symbol
> errors, now I get *undefined reference to pci_drv_register*. I have
> downloaded pci-scan.* and put them in the drivers/net directory with
> tulip.c. Any other suggestions?
>
> Thanks for your time,
>
> Erik Myllymaki
> erik@pacific-shores.com
>
>
>
> _______________________________________________
> tulip mailing list
> tulip@scyld.com
> http://www.scyld.com/mailman/listinfo/tulip
>