[tulip] Transmit lockup on file transfers
Erik Steffl
steffl@bigfoot.com
Tue, 12 Dec 2000 08:54:55 -0800
can you copy the file with no problems?
I would test with different sizes of files to see if it occurs from
certain size up.
erik
"Morrell, Mike A" wrote:
>
> I tried reinstall with an ext2 files system and still have the same problem.
> I am beginning to suspect a kernel issue.
>
> -----Original Message-----
> From: Erik Steffl [mailto:steffl@bigfoot.com]
> Sent: Monday, December 11, 2000 12:31 PM
> To: 'tulip@scyld.com'
> Subject: Re: [tulip] Transmit lockup on file transfers
>
> I have similar problem, card just stops tx-ing, but I don't get the
> same error message, ifconfig reports lots of carrier errors (and
> collisions). I think I have the same chip, but can't verify at the
> moment.
>
> is the half-duplex intentional? my card also says half duplex but the
> other end (intel pro/100 via crossover cable) thinks it's full duplex...
>
> I'm using the same driver...
>
> erik
>
> "Morrell, Mike A" wrote:
> >
> > I am trying to transfer a large file (1.3GB) between two machines using
> ftp.
> > The transfer starts and then locks up up after about 3 seconds. Both
> > machines are running V.92P of Donalds drivers on Mandrake 7.2 distros with
> > the transmitting machine being a fresh install for a server configuration.
> > Here are the error messages I get:
> >
> > eth1: Too much work during an interrupt, csr5=0xe46980c0.
> > eth1: Restarted Rx at 2048435 / 2048435
> >
> > Both NICs were working before when I had Mandrake 7.1 installed on the
> > server. I did use the Reiserfs though when I did the install. Maybe this
> has
> > something to do with it? I can reset the card by doing an ifdown/ifup. The
> > collision light on the hub is flashing a lot and it never did this before.
> >
> > Here is the output from tulip-diag (eth0 is connected to cable modem, eth1
> > to hub).
> >
> > tulip-diag.c:v2.04 9/26/2000 Donald Becker (becker@scyld.com)
> > http://www.scyld.com/diag/index.html
> > Index #1: Found a ADMtek AL985 Centaur-P adapter at 0x6400.
> > ADMtek AL985 Centaur-P chip registers at 0x6400:
> > fff98000 ffffffff ffffffff 077fc000 077fc200 fc664010 ff972117 ffffebff
> > fffe0000 fff597f8 00000000 fffe0000 00000000 00000200 00000000 c40ffec8
> > 00664010 804c0004 00000000 077fc160 f0000000 ffffc262 00000000 00000000
> > 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> > Port selection is 100mbps-SYM/PCS 100baseTx scrambler, half-duplex.
> > Transmit started, Receive started, half-duplex.
> > The Rx process state is 'Waiting for packets'.
> > The Tx process state is 'Idle'.
> > The transmit threshold is 128.
> > The Comet MAC registers are 1ebf5000 ffffc262 filter 8000000000000000.
> > Index #2: Found a Macronix 98715 PMAC adapter at 0x6600.
> > Macronix 98715 PMAC chip registers at 0x6600:
> > fff88000 ffffffff ffffffff 06fff800 06fffa00 ec660000 01a82202 e7ffebef
> > fffe0000 0fffcf08 fffc0000 fffe0000 40a1d0cc ffff0000 ffffffff fff00000
> > 0f340000 0f340000 0f340000 f0cffff0 2001527f 2001527f 2001527f 2001527f
> > 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f 2001527f
> > Port selection is 10mpbs-serial 100baseTx scrambler, full-duplex.
> > Transmit started, Receive started, full-duplex.
> > The Rx process state is 'Waiting for packets'.
> > The Tx process state is 'Idle'.
> > The transmit unit is set to store-and-forward.
> > tulip-diag.c:v2.04 9/26/2000 Donald Becker (becker@scyld.com)
> > http://www.scyld.com/diag/index.html
> > Index #1: Found a ADMtek AL985 Centaur-P adapter at 0x6400.
> > Port selection is 100mbps-SYM/PCS 100baseTx scrambler, half-duplex.
> > Transmit started, Receive started, half-duplex.
> > The Rx process state is 'Waiting for packets'.
> > The Tx process state is 'Idle'.
> > The transmit threshold is 128.
> > The Comet MAC registers are 1ebf5000 ffffc262 filter 8000000000000000.
> > EEPROM size is 8.
> > Ethernet MAC Station Address 00:50:bf:1e:62:c2.
> > Default connection type 'Autosense'.
> > PCI IDs Vendor 1317 Device 0985 Subsystem 1113 1216
> > PCI min_grant 255 max_latency 255.
> > CSR18 power-up setting 0x804c****.
> > Index #2: Found a Macronix 98715 PMAC adapter at 0x6600.
> > Port selection is 10mpbs-serial 100baseTx scrambler, full-duplex.
> > Transmit started, Receive started, full-duplex.
> > The Rx process state is 'Waiting for packets'.
> > The Tx process state is 'Idle'.
> > The transmit unit is set to store-and-forward.
> > EEPROM size is 6.
> > A simplifed EEPROM data table was found.
> > The EEPROM does not contain transceiver control information.
> > tulip-diag.c:v2.04 9/26/2000 Donald Becker (becker@scyld.com)
> > http://www.scyld.com/diag/index.html
> > Index #1: Found a ADMtek AL985 Centaur-P adapter at 0x6400.
> > Port selection is 100mbps-SYM/PCS 100baseTx scrambler, half-duplex.
> > Transmit started, Receive started, half-duplex.
> > The Rx process state is 'Waiting for packets'.
> > The Tx process state is 'Idle'.
> > The transmit threshold is 128.
> > The Comet MAC registers are 1ebf5000 ffffc262 filter 8000000000000000.
> > EEPROM size is 8.
> > Ethernet MAC Station Address 00:50:bf:1e:62:c2.
> > Default connection type 'Autosense'.
> > PCI IDs Vendor 1317 Device 0985 Subsystem 1113 1216
> > PCI min_grant 255 max_latency 255.
> > CSR18 power-up setting 0x804c****.
> > Index #2: Found a Macronix 98715 PMAC adapter at 0x6600.
> > Port selection is 10mpbs-serial 100baseTx scrambler, full-duplex.
> > Transmit started, Receive started, full-duplex.
> > The Rx process state is 'Waiting for packets'.
> > The Tx process state is 'Idle'.
> > The transmit unit is set to store-and-forward.
> > EEPROM size is 6.
> > A simplifed EEPROM data table was found.
> > The EEPROM does not contain transceiver control information.
> >
> > _______________________________________________
> > tulip mailing list
> > tulip@scyld.com
> > http://www.scyld.com/mailman/listinfo/tulip
>
> _______________________________________________
> tulip mailing list
> tulip@scyld.com
> http://www.scyld.com/mailman/listinfo/tulip
>
> _______________________________________________
> tulip mailing list
> tulip@scyld.com
> http://www.scyld.com/mailman/listinfo/tulip