No subject
manching@hongkong.com
manching@hongkong.com
Sun Aug 1 17:43:02 1999
Hi, I have installed RPM 6.0 + CLE 8.0 . My linux kernel is kernel-2.2.5-CLE15. I removed the RPM pcmcia packet and installed the pcmcia-cs-3.0.13 and tulip.c 0.91g . My LAN card is KingMax CardBus 10/100Mbps Ethernet card and my school network is 10Mbps, half duplex. I connect to the school network by DHCP client. Both the "Link" and the "TX/RX" LED light up properly. I can connect my linux to the internet and use my netscape. I may have done something wrong during the network and pcmcia setup because the Delaying network initializtion reported Fail. The eth0 can't connect to the network automatically when I reboot my linux. Any idea to solve the error?
Here is my pcmcia config:
"cardctl ident"
Socket 1:
product info: "CardBus", "10/100Mbps LAN Card", "PCB Rev3.2", "DTDKA25"
manfid: 0x8a01, 0x0100
function: 6 (network)
add info in "/etc/pcmcia/config.opts"
card "KingMax CardBus 10/100Mbps Ethernet card"
version "CardBus", "10/100Mbps LAN Card", "PCB Rev3.2", "DTDKA25"
#manfid 0x8a01, 0x0100
bind "tulip_cb"
"cat /var/log/messages"
Starting PCMCIA services:
pcmcia: modules
kernel: Linux PCMCIA Card Services 3.0.13
kernel: kernel build: 2.2.5-15CLE #2 Sun Aug 1 02:08:15 EDT 1999
kernel: options: [pci] [cardbus] [apm]
kernel: Intel PCIC probe:
kernel: TI 1220 PCI-to-CardBus at bus 0 slot 10, mem 0x68000000, 2 sockets
kernel: host opts [0]: [pwr save] [serial pci & irq] [no pci irq] [lat 168/1
76] [bus 32/34]
kernel: host opts [1]: [pwr save] [serial pci & irq] [no pci irq] [lat 168/1
76] [bus 35/37]
kernel: ISA irqs (scanned) = 3,4,5,11 status change on irq 11
modprobe: can't locate module eth0
modprobe: can't locate module eth0
pcmcia: cardmgr.
cardmgr[362]: starting, version is 3.0.13
cardmgr[362]: config error, file 'config' line 1326: syntax error
kernel: cs: IO port probe 0x1000-0x17ff: excluding 0x1000-0x103f 0x1400-0x140f
kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x300-0x307 0x378-0x37f 0x388
-0x38f 0x4d0-0x4d7
kernel: cs: IO port probe 0x0a00-0x0aff: clean.
cardmgr[362]: watching 2 sockets
cardmgr[362]: initializing socket 0
cardmgr[362]: socket 0: Serial or Modem
kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean.
cardmgr[362]: executing: 'insmod /lib/modules/2.2.5-15CLE/pcmcia/serial_cs.o'
kernel: tty02 at 0x03e8 (irq = 3) is a 16550A
cardmgr[362]: executing: './serial start ttyS2'
rc: Starting pcmcia succeeded
inet: inetd startup succeeded
cardmgr[362]: initializing socket 1
cardmgr[362]: socket 1: KingMax CardBus 10/100Mbps Ethernet card
cardmgr[362]: executing: 'insmod /lib/modules/2.2.5-15CLE/pcmcia/cb_enabler.o'
cardmgr[362]: executing: 'insmod /lib/modules/2.2.5-15CLE/pcmcia/tulip_cb.o'
kernel: cs: cb_config(bus 35): vendor 0x1011, device 0x0019
kernel: fn 0 bar 1: io 0x400-0x47f
kernel: fn 0 bar 2: mem 0xa00c2000-0xa00c23ff
kernel: fn 0 rom: mem 0xa0082000-0xa00c1fff
kernel: tulip_attach(bus 35, function 0)
kernel: tulip.c:v0.91g 7/16/99 becker@cesdis.gsfc.nasa.gov
kernel: eth0: Digital DS21143 Tulip rev 65 at 0x400, 00:A0:0C:90:1F:DC, IRQ 5.
kernel: eth0: EEPROM default media type Autosense.
kernel: eth0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)
block.
kernel: eth0: Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY
(2) block.
kernel: eth0: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4)
block.
kernel: eth0: Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM PHY (
4) block.
cardmgr[362]: executing: './network start eth0'
.
.
.
amd[492]: No networks.
amd[492]: My ip addr is 0x7f000001
.
.
.
linuxconf: Linuxconf final setup
rc: Starting linuxconf succeeded
rc: Starting local succeeded
PAM_pwdb[630]: (gdm) session opened for user root by (uid=0)
gnome-name-server[733]: starting
"cat /var/run/stab"
Socket 1: KingMax CardBus 10/100Mbps Ethernet card
1 network tulip_cb 0 eth0
"ifconfig"
eth0 Link encap:Ethernet HWaddr 00:A0:0C:90:1F:DC
inet addr:169.226.233.71 Bcast:169.226.239.255 Mask:255.255.248.0
UP BROADCAST RUNNING MTU:1500 Metric:1
RX packets:3516 errors:0 dropped:0 overruns:0 frame:0
TX packets:336 errors:0 dropped:0 overruns:0 carrier:0
collisions:49 txqueuelen:100
Interrupt:5 Base address:0x400
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:66 errors:0 dropped:0 overruns:0 frame:0
TX packets:66 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
"tulip-diag -a"
tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0x400.
Digital DS21143 Tulip chip registers at 0x400:
f8000000 ffffffff ffffffff dfda47f7 5f0f5ffe f0000010 b2420200 f3fe0000
e0000000 ffffcbf8 ffffffff 00000000 000052ca ffff0001 fffbffff 8ffb8000
Port selection is 10mpbs-serial, full-duplex.
Transmit stopped, Receive stopped, full-duplex.
The Rx process state is 'Stopped'.
The Tx process state is 'Stopped'.
The transmit threshold is 72.
"tulip-diag -e"
tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0x400.
Port selection is 10mpbs-serial, half-duplex.
Transmit started, Receive started, half-duplex.
The Rx process state is 'Waiting for packets'.
The Tx process state is 'Idle'.
The transmit threshold is 72.
Ethernet MAC Station Address 00:A0:0C:90:1F:DC.
EEPROM transceiver/media description for the Digital DS21143 Tulip chip.
Leaf node at offset 30, default media type 0800 (Autosense).
4 transceiver description blocks:
Media 10baseT, block type 2, length 6.
Serial transceiver for 10baseT (media type 0).
GP pin direction 08af GP pin data 00a1.
Media 10baseT-Full Duplex, block type 2, length 6.
Serial transceiver for 10baseT-Full Duplex (media type 4).
GP pin direction 08af GP pin data 00a1.
Media 100baseTx, block type 4, length 8.
SYM transceiver for 100baseTx (media type 3).
GP pin direction 08af GP pin data 00a1.
No media detection indication (command 80 61).
Media 100baseTx Full Duplex, block type 4, length 8.
SYM transceiver for 100baseTx Full Duplex (media type 5).
GP pin direction 08af GP pin data 00a1.
No media detection indication (command 80 61).
"tulip-diag -m"
tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0x400.
Port selection is 10mpbs-serial, half-duplex.
Transmit started, Receive started, half-duplex.
The Rx process state is 'Waiting for packets'.
The Tx process state is 'Idle'.
tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0x400.
Port selection is 10mpbs-serial, half-duplex.
Transmit started, Receive started, half-duplex.
The Rx process state is 'Waiting for packets'.
The Tx process state is 'Idle'.
The transmit threshold is 72.
No MII transceivers found!
Internal autonegotiation state is 'Negotiation complete'.
manching
email: manching@hongkong.com
___________________________________________________________________________
Get your hongkong.com freemail at http://www.hongkong.com
Free newsletters center at http://post4u.hongkong.com