Update on Sony Vaio w/DS21143
mbreuer@siac.com
mbreuer@siac.com
Wed Apr 14 13:27:28 1999
This is a multi-part message in MIME format.
--------------78AEFC86DBAA0991B31FD53F
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
Ok... I've made some additional progress with the docking station... I can now initialize the driver, and select a seemingly valid
tranceiver. However, each attempted tranceiver choice generates some sort of error. I've attached tulip-diag output (while tulip was
running with options=12 and options=0).
I've also attached snippets of syslog output from a variety of attempts to utilized the network with different options.
I'd appreciate any further insight anyone might have.
Thanks,
Michael Breuer
mbreuer@siac.com
--------------78AEFC86DBAA0991B31FD53F
Content-Type: text/plain; charset=us-ascii;
name="tulip-diag-log-opt12.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="tulip-diag-log-opt12.txt"
tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0xec00.
Digital DS21143 Tulip chip registers at 0xec00:
f8a08000 ffffffff ffffffff 00d51810 00d51a10 f0260000 b2422202 fbfffbff
e0000000 fff583ff ffffffff 00000000 000000c6 ffff0000 fff8ffff 8ff50008
Port selection is 10mpbs-serial, full-duplex.
Transmit started, Receive started, full-duplex.
The Rx process state is 'Waiting for packets'.
The Tx process state is 'Waiting for Tx to finish'.
The transmit threshold is 72.
EEPROM contents:
104d 801e 0000 0000 0000 0000 0000 0000
18c5 0104 0008 0146 5ba9 1e00 0000 0800
8604 0002 08ff 00f0 0286 ff01 f008 8600
0402 08ff 00f0 038d 0000 0000 e078 0001
0050 0018 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 7fac
0000 0000 0000 0008 0146 8398 0020 0000
0000 0000 0000 0000 0000 0000 0000 0635
ID CRC 0xc5 (vs. 0xc5), complete CRC 539f5722.
Ethernet MAC Station Address 08:00:46:01:A9:5B.
EEPROM transceiver/media description for the Digital DS21143 Tulip chip.
Leaf node at offset 30, default media type 0800 (Autosense).
4 transceiver description blocks:
Media 10baseT, block type 2, length 6.
Serial transceiver for 10baseT (media type 0).
GP pin direction 08ff GP pin data 00f0.
Media 10base2, block type 2, length 6.
Serial transceiver for 10base2 (media type 1).
GP pin direction 08ff GP pin data 00f0.
Media 10baseT-Full Duplex, block type 2, length 6.
Serial transceiver for 10baseT-Full Duplex (media type 4).
GP pin direction 08ff GP pin data 00f0.
Media MII, block type 3, length 13.
MII interface PHY 0 (media type 11).
21143 MII initialization sequence is 0 words:.
21143 MII reset sequence is 0 words:.
Media capabilities are 7800, advertising 01e1.
Full-duplex map 5000, Threshold map 1800.
No MII interrupt.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
No MII transceivers found!
Internal autonegotiation state is 'Autonegotiation disabled'.
--------------78AEFC86DBAA0991B31FD53F
Content-Type: text/plain; charset=us-ascii;
name="tulip-diag-log-opt0.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="tulip-diag-log-opt0.txt"
tulip-diag.c:v1.10 4/12/99 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Index #1: Found a Digital DS21143 Tulip adapter at 0xec00.
Digital DS21143 Tulip chip registers at 0xec00:
f8a08000 ffffffff ffffffff 00d50010 00d50210 f0260000 320e2002 fbfffbff
e0000000 fff583ff ffffffff 00000000 000000c6 ffff0000 fffbffff 8ffc0000
Port selection is MII, half-duplex.
Transmit started, Receive started, half-duplex.
The Rx process state is 'Waiting for packets'.
The Tx process state is 'Waiting for Tx to finish'.
The transmit threshold is 128.
EEPROM contents:
104d 801e 0000 0000 0000 0000 0000 0000
18c5 0104 0008 0146 5ba9 1e00 0000 0800
8604 0002 08ff 00f0 0286 ff01 f008 8600
0402 08ff 00f0 038d 0000 0000 e078 0001
0050 0018 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 7fac
0000 0000 0000 0008 0146 8398 0020 0000
0000 0000 0000 0000 0000 0000 0000 0635
ID CRC 0xc5 (vs. 0xc5), complete CRC 539f5722.
Ethernet MAC Station Address 08:00:46:01:A9:5B.
EEPROM transceiver/media description for the Digital DS21143 Tulip chip.
Leaf node at offset 30, default media type 0800 (Autosense).
4 transceiver description blocks:
Media 10baseT, block type 2, length 6.
Serial transceiver for 10baseT (media type 0).
GP pin direction 08ff GP pin data 00f0.
Media 10base2, block type 2, length 6.
Serial transceiver for 10base2 (media type 1).
GP pin direction 08ff GP pin data 00f0.
Media 10baseT-Full Duplex, block type 2, length 6.
Serial transceiver for 10baseT-Full Duplex (media type 4).
GP pin direction 08ff GP pin data 00f0.
Media MII, block type 3, length 13.
MII interface PHY 0 (media type 11).
21143 MII initialization sequence is 0 words:.
21143 MII reset sequence is 0 words:.
Media capabilities are 7800, advertising 01e1.
Full-duplex map 5000, Threshold map 1800.
No MII interrupt.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
21140 Non-MII transceiver with media 0 (10baseT).
CSR12 control port setting 00, command 00 00.
Media detection by looking for a 1 on bit 0 of the CSR12 control port.
No MII transceivers found!
Internal autonegotiation state is 'Autonegotiation disabled'.
--------------78AEFC86DBAA0991B31FD53F
Content-Type: text/plain; charset=us-ascii;
name="tulip-syslog.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="tulip-syslog.txt"
[options=0]
Apr 14 11:37:25 mbreuer kernel: Found Digital DS21143 Tulip at PCI I/O address 0xec00.
Apr 14 11:37:25 mbreuer kernel: tulip.c:v0.90z 4/7/99 becker@cesdis.gsfc.nasa.gov
Apr 14 11:37:25 mbreuer kernel: eth0: Digital DS21143 Tulip rev 65 at 0xec00, 08:00:46:01:A9:5B, IRQ 9.
Apr 14 11:37:25 mbreuer kernel: eth0: EEPROM default media type Autosense.
Apr 14 11:37:25 mbreuer kernel: eth0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
Apr 14 11:37:25 mbreuer kernel: eth0: Index #1 - Media 10base2 (#1) described by a 21142 Serial PHY (2) block.
Apr 14 11:37:25 mbreuer kernel: eth0: Index #2 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2) block.
Apr 14 11:37:25 mbreuer kernel: eth0: MII interface PHY 0, setup/reset sequences 0/0 long, capabilities e0 78.
Apr 14 11:37:25 mbreuer kernel: eth0: Index #3 - Media MII (#11) described by a 21142 MII PHY (3) block.
Apr 14 11:37:25 mbreuer kernel: eth0: ***WARNING***: No MII transceiver found!
Apr 14 11:37:25 mbreuer network: Enabling IPv4 packet forwarding succeeded
Apr 14 11:37:26 mbreuer network: Bringing up interface lo succeeded
Apr 14 11:37:27 mbreuer network: Bringing up interface eth0 succeeded
Apr 14 11:37:31 mbreuer kernel: nfs: server pid396@mbreuer:/net OK
Apr 14 11:37:31 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 10baseT.
Apr 14 11:37:31 mbreuer kernel: eth0: 21143 negotiation failed, status 000000c6.
Apr 14 11:37:31 mbreuer kernel: eth0: Testing new 21143 media 100baseTx.
Apr 14 11:37:34 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 100baseTx.
Apr 14 11:37:34 mbreuer kernel: eth0: No 21143 100baseTx link beat, 000000c6, trying NWay.
Apr 14 11:37:37 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 10baseT.
Apr 14 11:37:37 mbreuer kernel: eth0: 21143 negotiation failed, status 000000c6.
Apr 14 11:37:37 mbreuer kernel: eth0: Testing new 21143 media 100baseTx.
Apr 14 11:37:40 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 100baseTx.
Apr 14 11:37:40 mbreuer kernel: eth0: No 21143 100baseTx link beat, 000000c6, trying NWay.
Apr 14 11:37:43 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 10baseT.
Apr 14 11:37:43 mbreuer kernel: eth0: 21143 negotiation failed, status 000000c6.
Apr 14 11:37:43 mbreuer kernel: eth0: Testing new 21143 media 100baseTx.
Apr 14 11:37:46 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 100baseTx.
Apr 14 11:37:46 mbreuer kernel: eth0: No 21143 100baseTx link beat, 000000c6, trying NWay.
Apr 14 11:37:46 mbreuer kernel: eth0: Tx hung, 24 vs. 9.
Apr 14 11:37:46 mbreuer kernel: eth0: 21140 transmit timed out, status f0260000, SIA 000000c6 ffff0000 fffbffff 8ff40000, resetting...
Apr 14 11:37:46 mbreuer kernel: eth0: transmit timed out, switching to 10baseT media.
Apr 14 11:37:49 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 10baseT.
Apr 14 11:37:49 mbreuer kernel: eth0: 21143 negotiation failed, status 000000c6.
Apr 14 11:37:49 mbreuer kernel: eth0: Testing new 21143 media 100baseTx.
Apr 14 11:37:50 mbreuer kernel: eth0: 21140 transmit timed out, status f0260000, SIA 000000c6 ffff0000 fffbff7f 8ff50008, resetting...
Apr 14 11:37:50 mbreuer kernel: eth0: transmit timed out, switching to MII media.
Apr 14 11:37:52 mbreuer kernel: eth0: 21143 negotiation status 000000c6, MII.
Apr 14 11:37:52 mbreuer kernel: eth0: MII status ffff, Link partner report ffff.
Apr 14 11:37:55 mbreuer kernel: eth0: Transmit timeout using MII device.
Apr 14 11:37:58 mbreuer network: Shutting down interface eth0 succeeded
Apr 14 11:37:58 mbreuer network: Disabling IPv4 packet forwarding succeeded
[options 12]
Apr 14 11:41:58 mbreuer kernel: tulip.c:v0.90z 4/7/99 becker@cesdis.gsfc.nasa.gov
Apr 14 11:41:58 mbreuer kernel: eth0: Digital DS21143 Tulip rev 65 at 0xec00, 08:00:46:01:A9:5B, IRQ 9.
Apr 14 11:41:58 mbreuer kernel: eth0: EEPROM default media type Autosense.
Apr 14 11:41:58 mbreuer kernel: eth0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
Apr 14 11:41:58 mbreuer kernel: eth0: Index #1 - Media 10base2 (#1) described by a 21142 Serial PHY (2) block.
Apr 14 11:41:58 mbreuer kernel: eth0: Index #2 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2) block.
Apr 14 11:41:58 mbreuer kernel: eth0: MII interface PHY 0, setup/reset sequences 0/0 long, capabilities e0 78.
Apr 14 11:41:58 mbreuer kernel: eth0: Index #3 - Media MII (#11) described by a 21142 MII PHY (3) block.
Apr 14 11:41:58 mbreuer kernel: eth0: ***WARNING***: No MII transceiver found!
Apr 14 11:42:06 mbreuer network: Enabling IPv4 packet forwarding succeeded
Apr 14 11:42:06 mbreuer network: Bringing up interface lo succeeded
Apr 14 11:42:06 mbreuer kernel: eth0: Using user-specified media 10baseT(forced).
Apr 14 11:42:06 mbreuer network: Bringing up interface eth0 succeeded
Apr 14 11:42:10 mbreuer kernel: nfs: server pid396@mbreuer:/net OK
Apr 14 11:42:11 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 10baseT.
Apr 14 11:42:30 mbreuer kernel: eth0: 21140 transmit timed out, status f0260000, SIA 000000c6 ffff0000 fff8ffff 8ff50008, resetting...
Apr 14 11:43:05 mbreuer last message repeated 7 times
Apr 14 11:43:10 mbreuer kernel: eth0: 21140 transmit timed out, status f0260000, SIA 000000c6 ffff0000 fff8ffff 8ff50008, resetting...
Apr 14 11:43:11 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 10baseT.
Apr 14 11:43:15 mbreuer kernel: eth0: 21140 transmit timed out, status f0260000, SIA 000000c6 ffff0000 fff8ffff 8ff50008, resetting...
Apr 14 11:43:50 mbreuer last message repeated 7 times
Apr 14 11:44:10 mbreuer last message repeated 4 times
Apr 14 11:44:11 mbreuer kernel: eth0: 21143 negotiation status 000000c6, 10baseT.
Apr 14 11:44:14 mbreuer network: Shutting down interface eth0 succeeded
--------------78AEFC86DBAA0991B31FD53F--