Aiee!

[Paul E. Wick]

Hello,

I am tring to use a Linksys EtherFast Cardbus 21143 PC Card
in my Compaq Armada 7770 so far without success. (It works
great in Windows 95 and NT thought.) The network is a 
10baseT half duplex and I'm connected to an HP hub. The
version of Linux is Redhat and I'm using both 2.0.35 and
2.1.124 kernels. PCMCIA is version 3.0.5 or 3.0.6. Tulip is .89K.

When the network script runs I get a panic

Kernel panic: skput:over: 0486d644:16444
In swapper task - not syncing

or a

Aiee: scheduling in interrupt 00124f61

depending on which version of PCMCIA and how I've set up the 
networking config. I've tried various memory windows and IRQs.
I've tried to select different ports. For example
see below the "options=12".

I hope someone has some ideas because I'm in way over my
head! See various config info below.

Thanks,
Paul Wick
pwick@teleport.com


tulip-diag.c:v1.06 9/18/98 Donald Becker
(becker@cesdis.gsfc.nasa.gov)
Digital DC21040 Tulip Tulip chip registers at 0xa00: 
fe000000 ffffffff ffffffff 56e5f3ff bfe9ff7f f0000000 b20e0000 f3fe0000
e0000000 fff083ff ffffffff fffe0000 000000c6 ffff0000 fff80000 8ff9c000
The Rx process state is 'Stopped'. 
The Tx process state is 'Stopped'.
Transmit stopped, Receive stopped, half-duplex. The transmit
threshold is 128. Port selection is MII, half-duplex.tulip-diag.c:v1.06
9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov) MII PHY found at
address 0, status 0x782d.



Oct  7 09:27:53 myhost kernel: Linux PCMCIA Card Services 3.0.6
Oct  7 09:27:53 myhost kernel:   kernel build: 2.0.35 #1 Thu Oct 1  09:11:29 PDT 1998
Oct  7 09:27:53 myhost kernel:   options:  [pci] [cardbus]
Oct  7 09:27:53 myhost kernel: Intel PCIC probe: 
Oct  7 09:27:53 myhost kernel:   TI 1131 PCI-to-CardBus at bus 0 slot 12, 
mem 0x7fffe000, 2 sockets
Oct  7 09:27:53 myhost kernel:     host opts [0]: [pci + serial irq] [pci
irq 11] [lat 66/176] [bus 1/1]
Oct  7 09:27:53 myhost kernel:     host opts [1]: [pci + serial irq] [pci
irq 11] [lat 66/176] [bus 2/2]
Oct  7 09:27:53 myhost kernel:     ISA irqs (scanned) = 3,4,7,9,10,15
status change on irq 15
Oct  7 09:27:53 myhost cardmgr[211]: starting, version is 3.0.6
Oct  7 09:27:53 myhost cardmgr[211]: watching 2 sockets
Oct  7 09:27:53 myhost kernel: cs: IO port probe 0x0d00-0x0dff: clean.
Oct  7 09:27:53 myhost kernel: cs: IO port probe 0x0b00-0x0bff: clean.
Oct  7 09:27:53 myhost kernel: cs: IO port probe 0x0a00-0x0aff: clean.



Oct  7 16:01:29 localhost cardmgr[201]: initializing socket 0
Oct  7 16:01:29 localhost cardmgr[201]: socket 0: Linksys EtherFast 10/100
Oct  7 16:01:29 localhost cardmgr[201]: executing: 'insmod
/lib/modules/2.0.35/pcmcia/cb_enabler.o'
Oct  7 16:01:29 localhost cardmgr[201]: executing: 'insmod
/lib/modules/2.0.35/pcmcia/tulip_cb.o debug=3 options=12'
Oct  7 16:01:29 localhost kernel: cs: cb_config(bus 1): vendor 0x1011,
device 0x0019
Oct  7 16:01:29 localhost kernel:   fn 0 bar 1: io 0xb00-0xb7f
Oct  7 16:01:29 localhost kernel:   fn 0 bar 2: mem 0xa00c0000-0xa00c007f
Oct  7 16:01:29 localhost kernel:   fn 0 rom: mem 0xa0080000-0xa00bffff
Oct  7 16:01:29 localhost kernel: tulip_attach(bus 1, function 0)
Oct  7 16:01:29 localhost kernel: tulip.c:v0.89K 8/8/98
becker@cesdis.gsfc.nasa.gov
Oct  7 16:01:29 localhost kernel: eth0: Digital DS21143 Tulip at 0xb00, 00
e0 98 02 ee 40, IRQ 9.
Oct  7 16:01:29 localhost kernel: eth0:  EEPROM default media type
Autosense.
Oct  7 16:01:29 localhost kernel: eth0:  Index #0 - Media 10baseT (#0)
described by a 21142 Serial PHY (2) block.
Oct  7 16:01:29 localhost kernel: eth0:  Index #1 - Media 10baseT-FD (#4)
described by a 21142 Serial PHY (2) block.
Oct  7 16:01:29 localhost kernel: eth0:  Index #2 - Media 100baseTx (#3)
described by a 21143 SYM PHY (4) block.
Oct  7 16:01:29 localhost kernel: eth0:  Index #3 - Media 100baseTx-FD
(#5) described by a 21143 SYM PHY (4) block.
Oct  7 16:01:29 localhost kernel: eth0: Checking for MII transceivers...
Oct  7 16:01:29 localhost kernel: eth0:  MII transceiver found at MDIO
address 0, config 1000 status 7809.