[tulip] (problems!!) EtherExpress PRO/100 Mobile 32 bitcardbus --

Jon Oringer jon@advercast.com
Thu, 20 Jul 2000 18:53:49 -0700


I just installed Redhat 6.2 -- Im having problems getting the eepro100 32
bit
PCMCIA cardbus to work..

any network activity after ifup eth0 causes the following message
"eth0": 21140 transmit timed out, status ...
eth0: Tx hung, 15 vs. 9

Facts:
- link light on PCMCIA dongle is ON, link light on HUB is OFF
- EEPROM is reported missing..
- exclude irq 3 is commented out on /etc/pcmcia/config.opts
- my laptop is a Sony PCG-505TX

I found other questions like this on the list -- but couldn't find an
answer.. does anybody have one? or could point me to the answer?

here is more dump info....

tulip-diag.c:v2.01 5/10/2000 Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
Index #1: Found a Digital DS21143 Tulip adapter at 0x400.
Digital DS21143 Tulip chip registers at 0x400:
  ffa08000 ffffffff ffffffff 00249810 00249a10 f0000102 b3860000 f3fe0000
  e0000000 fff0d323 ffffffff fffe0000 000000c6 ffff0000 fffbff7f 8ff00008
 Port selection is 100mbps-SYM/PCS 100baseTx scrambler, half-duplex.
 Transmit stopped, Receive stopped, half-duplex.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 128.
  The NWay status register is 000000c6.
You have an Intel CardBus card with an incomplete EEPROM.
The station address is 00:a0:c9:79:d6:23
New EEPROM contents would be:
  8086 0001 0087 0000 0000 0000 0000 0000
  00c4 0103 a000 79c9 23d6 1e00 0000 0800
  8604 0002 08af 00a5 0286 af04 a508 8800
  0304 08af 00a5 8061 0488 af05 a508 6100
  0000 0000 0000 0000 0000 0000 0000 0000
  0000 0000 0000 0000 0000 0000 0000 0000
  0000 0000 0000 0000 0000 0000 0000 0000
  0000 0000 0000 0000 0000 0000 0000 4448
 ID CRC 0xc4 (vs. 0xc4), complete CRC 4448.
  Internal autonegotiation state is 'Autonegotiation disabled'.

--------------------------------------------------------------------------

Linux PCMCIA Card Services 3.1.8
  kernel build: 2.2.14-5.0 #1 Tue Mar 7 20:53:41 EST 2000
  options:  [pci] [cardbus] [apm]
Intel PCIC probe:
  Ricoh RL5C475 PCI-to-CardBus at bus 0 slot 10, mem 0x68000000, 1 socket
    host opts [0]: [isa irq] [io 3/6/1] [mem 3/6/1] [no pci irq] [lat
168/176] [bus 32/34]
    ISA irqs (default) = 3,4,5,7,10,11,12,15 polling interval = 1000 ms
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x140-0x147 0x170-0x177
0x220-0x22f 0x320-0x327 0x370-0x37f 0x388-0x38f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: cb_alloc(bus 32): vendor 0x1011, device 0x0019
ROM image dump:
  image 0: 0x000000-0x0001ff, signature PCIR
cs: cb_config(bus 32)
  fn 0 bar 1: io 0x400-0x47f
  fn 0 bar 2: mem 0x600c0000-0x600c007f
  fn 0 rom: mem 0x60080000-0x600bffff
cs: cb_enable(bus 32)
  bridge io map 0 (flags 0x21): 0x400-0x47f
  bridge mem map 0 (flags 0x1): 0x60080000-0x600c0fff
tulip_attach(bus 32, function 0)
tulip.c:v0.91 4/14/99 becker@cesdis.gsfc.nasa.gov (modified by
danilo@cs.uni-magdeburg.de for XIRCOM CBE, fixed by Doug Ledford)
eth0: Digital DS21143 Tulip rev 48 at 0x400, EEPROM not present,
00:4C:69:6E:75:79, IRQ 3.

-----------------------------------------------

[root@vaio /root]# ifup eth0
[root@vaio /root]# telnet 192.168.0.1
Trying 192.168.0.1...
telnet: Unable to connect to remote host: No route to host
[root@vaio /root]# eth0: Tx hung, 15 vs. 9.
eth0: 21140 transmit timed out, status f0260000, SIA 000000c6 ffff0000
fffbff7f
8ff00008, resetting...
eth0: Tx hung, 15 vs. 9.
eth0: 21140 transmit timed out, status f0260000, SIA 000000c6 ffff0000
fffbff7f
8ff00008, resetting...