more NetGear mising ARPs

jferg jferg@2boot.com
Mon May 24 10:48:05 1999


This is a multi-part message in MIME format.
--------------31F8DEED76A612C53106861C
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit

Neale Banks wrote:

> With 2.0.36 and tulip.c:v0.89H on a not-so-slow machine (349.80 bogomips)
> I appear to be bumping into this problem :-(
>
> Originally this machine was happily working, plugged in to a NetGear
> 10/100 "hub" (IIRC, a DS516) on a busyish network.  The machine was moved
> to a 10Mb hub on a _quiet_ subnet and now has missing-arp problems - worse
> with the Cisco 25xx which is the gateway on this subnet (the other linux
> box on the subnet is OK if you first arp from that, with the Cisco it's
> much less inclined to talk (even with attempting to talk from the Cisco)).
>
> >From dmesg:
>
> tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
> eth0: Lite-On 82c168 PNIC at 0xe800, 00 a0 cc 40 0a a7, IRQ 10.
> eth0:  MII transceiver found at MDIO address 1, config 1000 status 782d.
> eth0:  Advertising 01e1 on PHY 1, previously advertising 01e1.
> eth0: Changing PNIC configuration to half-duplex, CSR6 816e0000.
>
> >From /proc/pci:
>
> PCI devices found:
>   Bus  0, device  11, function  0:
>     Ethernet controller: Lite-on LNE100TX (rev 33).
>       Medium devsel.  Fast back-to-back capable.  IRQ 10.  Master Capable.  Latency=64.
>       I/O at 0xe800.
>       Non-prefetchable 32 bit memory at 0xe9000000.
>
> Turning debug up to three didn't produce anything obviously "interesting"
> (but the first time I booted with debug=3 the arp to the Cisco worked,
> subsequent tests suggest this may have been a fluke).
>
> >From ifconfig:
>
> eth0      Link encap:Ethernet  HWaddr 00:A0:CC:40:0A:A7
>           inet addr:a.b.c.20  Bcast:a.b.c.23  Mask:255.255.255.248
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:266 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:247 errors:0 dropped:0 overruns:0 carrier:0
>           Collisions:0
>           Interrupt:10 Base address:0xe800
>
> On occasions where the system is failing arp for all its neighbours, Tx
> packets increments but Rx packets does _not_ and the arp entries are
> marked as incomplete.
>
> Anyone have any idea what might be happening here, or how to work around
> this?
>
> I'll try to load and compile v0.91 of tulip.c tomorrow to see how that
> performs.
>
> Thanks,
> Neale.

Check half/full duplex status of everything connected to hub (when you say hub, I assume
you mean a PHY-level repeater; they don't handle full-duplex very well)

--
Joe Ferguson, ApeX Systems Integration Corp.
Voice:  919.468.8150
FAX:    919.468.5288
email:  jferg@2boot.com



--------------31F8DEED76A612C53106861C
Content-Type: text/x-vcard; charset=us-ascii;
 name="jferg.vcf"
Content-Transfer-Encoding: 7bit
Content-Description: Card for jferg
Content-Disposition: attachment;
 filename="jferg.vcf"

begin:vcard 
n:Ferguson;Joe
x-mozilla-html:FALSE
org:ApeX Systems Integration Corp.
adr:;;;;;;
version:2.1
email;internet:jferg@2boot.com
title:Tech Director
x-mozilla-cpt:;0
fn:Joe Ferguson
end:vcard

--------------31F8DEED76A612C53106861C--